meta data for this page
  •  

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
actor:relay_moduls [2026/05/14 19:53] – vamsanactor:relay_moduls [2026/05/14 22:00] (current) – [Current Required] vamsan
Line 3: Line 3:
  
 Understanding relay voltage ratings is essential for microcontrollers. For Arduino, 5V/3.3V relays are typical, whereas Raspberry Pi Micro and ESP32/3286 generally require 3.3V relays.  Understanding relay voltage ratings is essential for microcontrollers. For Arduino, 5V/3.3V relays are typical, whereas Raspberry Pi Micro and ESP32/3286 generally require 3.3V relays. 
 +
 +For high-speed AC switching, it is recommended to use a [[ssr_moduls|Multi-channel Solid State Relay (SSR) Module]] instead.
 +
 +{{ :actor:multi_channel_relay_1.png |Multi-channel optocoupled relay module}}
  
 These voltage ratings, such as //"5VDC"// or //"3VDC,"// are marked on the relays along with the maximum load capacity for AC and DC, for example, 10A at 250V AC or 30V DC, and 12A at 125V AC or 28V DC. In my experience, these maximum values are often overstated; I usually cut them in half. For example, for 240V AC, I consider a safe maximum of 5A, roughly 1000 Watts. These voltage ratings, such as //"5VDC"// or //"3VDC,"// are marked on the relays along with the maximum load capacity for AC and DC, for example, 10A at 250V AC or 30V DC, and 12A at 125V AC or 28V DC. In my experience, these maximum values are often overstated; I usually cut them in half. For example, for 240V AC, I consider a safe maximum of 5A, roughly 1000 Watts.
  
 +{{ :actor:multi_channel_relay_2.png?400 |Multi-channel optocoupled relay module schema}}
  
-{{ :actor:multi_channel_relay_1.png |Multi-channel optocoupled relay module}} 
  
 ==== Current Required ==== ==== Current Required ====
Line 19: Line 23:
  
 <color red>If the Arduino output becomes overloaded, the unit will turn off and then restart. If the overload continues, the relays will cycle on and off, producing a distinctive clicking sound.</color> <color red>If the Arduino output becomes overloaded, the unit will turn off and then restart. If the overload continues, the relays will cycle on and off, producing a distinctive clicking sound.</color>
 +
 +{{page>:tarhal}}
  
  
Line 28: Line 34:
 |HFD4/3-S \\ (Raw Relay)|1 Channel (Component)|3V DC (Standalone coil)|220V DC @ 2A|250V AC @ 0.5A|33.3 mA (Requires external driver circuit/diode)| |HFD4/3-S \\ (Raw Relay)|1 Channel (Component)|3V DC (Standalone coil)|220V DC @ 2A|250V AC @ 0.5A|33.3 mA (Requires external driver circuit/diode)|
 |FY-T734 \\ (GEYA)|4 Channels|5V DC, 12V or 24V AC/DC|30V DC @ 10A|250V AC @ 10A|~21.8 mA (Industrial terminal input)| |FY-T734 \\ (GEYA)|4 Channels|5V DC, 12V or 24V AC/DC|30V DC @ 10A|250V AC @ 10A|~21.8 mA (Industrial terminal input)|
 +
 +===== Sensor topics on lamaPLC =====
 +{{topic>sensor}}
 +
 +\\
 +\\
 +{{tag>Multi-channel optocoupled relay actor modul Arduino HL-54 HW-316 KY-019 HFD4/3-S FY-T734 Geya}}
 +\\
 +This page has been accessed for: Today: {{counter|today}}, Until now: {{counter|total}}